cutback bitumen SC-250


cutback bitumen SC-250

 

General information of cutback bitumen SC-250

Cutback asphalt is an asphalt cement that has a solvent or distillate such as gasoline, diesel fuel, kerosene, or naphtha added to make the asphalt liquid at ambient temperatures and improve its ability to coat aggregates. Two letters followed by a numerical digit designate or name a cutback asphalt.
Cutback asphalt can contain between 12 and 40 percent distillate. The high demand for the distillates to be used in energy applications and ever-increasing air quality regulations have caused a steady decline in the use of cutback asphalt.
The SC liquid asphalt may be obtained by fluxing an asphalt cement with a less volatile distillate such as gas oil. The SC-
70 and SC-250 grade cutback asphalts are very similar to residual refinery products that are used as heavy fuel oils such as bunker C or Number six fuel oils. These SC cutback materials, whether straight run or fluxed with a relatively non-volatile material such as gas oil, are also known as “road oils”.

Uses of cutback bitumen SC-250

Current common uses are in penetrating prime coats and in producing patching or stockpile mixtures. Cutback asphalt used in mixing with aggregate will usually contain an adhesion agent to assist in the coating of the aggregate surface.

Cutback agents are used to lower the viscosity of bitumen when it is applied as a primer to the surface of a road pavement aggregate base course or substrate. Kerosene is used as a bitumen cutback agent at different concentrations according to local conditions and requirements.

The cutback bitumen is ideal for prime coat and cold applied because of easy uses and no need to thinning and heating.

Cutback bitumen SC-250 consist of initial incorporation of asphalt into the surface of non-asphalt based course preparatory to any superimposed treatment of construction.

The cutback asphalt SC-250 applying to waterproofing of surfaces plug capillary voids, coat and bond loose mineral particles.

Packing of cutback bitumen SC-250

Packing of cutback bitumen SC-250 is in the new thick steel drum on the pallet to prevent any leak inside of container also bulk in bitutainers and tanker.

Safety of cutback bitumen SC-250

Refer to Safety Data sheets before use.
Transport, use and store at the lowest temperature possible.
Eliminate all potential ignition sources during application.
Avoid breathing vapors. Avoid contact with skin.
Always wear appropriate PPE including heat protection when used hot.
DO NOT allow product or washings to enter stormwater or sewer systems.

Specification of cutback bitumen SC-250

property

specification limit

 Test method

Min

Max

Kinematic viscosity at 60°C [140°F], mm2/s

250

500

ASTM D2170

Flashpoint(Cleveland open cup), °C [°F]

 60

 —

ASTM D92

distillate test

Total distillate to 360°C [680°F], volume %

25

ASTM D402

Solubility, %

95

— 

ASTM D2024

Kinematic viscosity on distillation residue at 60°C [140°F], mm2/s

400

 10000

ASTM D2170

Asphalt residue:

Residue of 100 penetration, %

50

— 

ASTM D243

Ductility of 100 penetration residue at 25°C [77°F], cm

50

— 

ASTM D113

Water, %

0.5 

ASTM D95

 

 

 

 

 

 

 

 

 

 

 

BITUMENSHOP Co. guaranty the quality of cutback SC-250 with the arrangement of the international inspectors to check quality and quantity of the bitumen on each shipment during the loading to vessel and controlling the production by QC team via batch test report before shipping. BITUMENSHOP guaranty the quality to meet with ASTM/EN 15322:2009.

 

 

 

 

Submit to FacebookSubmit to Google PlusSubmit to TwitterSubmit to LinkedIn